XP Xtreme Hunter Upgrade - XTR-115E - Upgrade for Deus 2

Save $123.35

Price:
Sale price$1,699.00 Regular price$1,822.35
Availability:
Sold out
Returns:
Final sale, not returnable. Refund policy
Questions:
Call 256-284-2247 and talk to someone who runs this gear. Authorized dealer.

Authorized XP dealer. The manufacturer's warranty applies.

Description

This product is the XTR-115E coils, stem and case ONLY. You MUST own an XP DEUS II remote control running software V2.0 or higher for it to work.

We know this is a bit confusing - If you have any questions call us at 256-284-2247.

XP Xtrem Hunter XTR-115E: Turn the DEUS II Remote You Own Into a Two-Box Deep Seeker

You already carry the most capable part of a two-box deep seeker in your pocket: the DEUS II remote. The XP Xtrem Hunter XTR-115E upgrade kit adds the rest, the XTR115 TX and RX coils on the S-Telescopic stem with its weatherproof case, and your remote switches to a dedicated Xtrem Hunter interface the moment you pair the frame as a new coil. XP rates the system to large targets up to 5 m (16 ft), naturally blind to the nails and small surface targets that mask a deep cache on a conventional machine, and one click back to a standard DEUS II coil confirms the target before you dig. This page says plainly who it is for, which kit to buy, which settings matter, where it works and where it does not, and the software prerequisite that decides whether it pairs. Most dealers spell it Xtreme Hunter; XP spells it XTREM HUNTER; it is the same machine.

At a glance

The XTR-115E is the Xtrem Hunter frame without a remote or headphones: XTR115 TX and RX FMF coils, S-Telescopic stem, USB-C cable, fasteners and strap, English manual, and the XTR-CASE115 case. It requires a DEUS II remote control on software V2.0 or higher (V4.1 is the newest release as of October 30, 2026); no charger is included. 2.9 kg (6.4 lb) with the remote fitted, more than 10 hours of battery, five-year warranty.

Exclusive History Seekers bonus: free with every XP Xtreme Hunter

Buy your XP Xtreme Hunter from History Seekers and receive a free 1-year subscription to American Digger Magazine, the definitive print resource for relic hunters, coin shooters, and serious diggers. Real finds, real research, and real history delivered directly to your door. This bonus is available exclusively through HistorySeekers.net.

Notice: the free subscription offer applies strictly to listed prices. It cannot be combined with other discount codes or promotions. If a coupon or promotional discount is used at checkout, the free magazine subscription is excluded.

XP Xtrem Hunter XTR-115E two-box frame with front TX and rear RX coils on the XTR stem

What Is in the XTR-115E Kit

XP's manual lists the parts and marks the remote and headphones "depending on version"; this is the version without them.

  • XTR115 TX and RX FMF coils: the front coil carries the wireless transmitter and the battery, the back coil connects to it by cable, both mounted on the two-part aluminum frame.
  • XTR-STEM S-Telescopic stem with adjustable handle and support, plus the carrying strap and the knurled fastening screws (two 5 x 30 mm, four 5 x 16 mm, one 4 x 12 mm).
  • USB-C charging cable (no charger: use any 1 A or stronger USB charger, such as your DEUS II's) and the English Xtrem Hunter manual.
  • XTR-CASE115 weatherproof XP case.
  • Not included: the DEUS II remote control and the headphones. Your own DEUS II remote runs it, and the headphones already paired to that remote carry its audio.

XP Xtrem Hunter depth graphic: two-box detector over buried cache and tank targets, depth scale to 5 m / 16 ft

Why a Two-Box Deep Seeking Metal Detector, and Why This One

XP's manual puts the problem plainly: a conventional detector hears a small target near the surface and a large mass at depth as roughly the same signal, so a nearby nail can mask a deep cache and a day on a good site goes to digging surface junk. The Xtrem Hunter's coil geometry, a transmitter coil in front and a receiver coil behind on a rigid 1.20 m (3.94 ft) frame, makes small surface targets naturally invisible to it, so it can penetrate the top layers of the ground and report what lies beneath them. Earlier two-box machines ran a single low frequency, false-signalled on every height change while walking and needed Sensitivity cut hard to behave; XP's Fast Multi Frequency (FMF) platform reduced that, which is why the factory ground setting works in most ground without retuning. XP rates it to large targets up to 5 m (16 ft) deep; the manual's own examples show a 30 cm (12 in) target still giving a clear but faint signal past 1 m (3 ft). Depth scales with target size, and XP's figure is a large-target ceiling, not a coin depth.

Spec XP Xtrem Hunter What it means in the field
Technology Simultaneous Fast Multi Frequency (FMF), two-box TX and RX coils; highest fundamental frequency 7.35 kHz Stable on more ground than single-frequency two-box machines, with far less retuning while you walk
Detection type Non-motion with adjustable Auto Tune (OFF to 3) You walk the frame forward over the ground rather than sweeping; a threshold hum breaks over a target
Depth Up to 5 m (16 ft) on large targets, per XP Caches, strongboxes, artillery shells, tanks and pipes; never single coins
Display Real-time recording of the last 4 seconds with Play / Pause Signal strength estimates depth, signal duration estimates size; a shallow target draws a double lobe, a deep one a single strong lobe
Iron handling Discri IAR (Iron Amplitude Rejection) OFF to 5 Moderate iron such as anchors, hammers and horseshoes gives a low tone and shows in gray; small iron is ignored by design
Controller DEUS II remote control (V2.0 or higher), paired as a coil The remote switches to a dedicated Xtrem Hunter interface; select a standard DEUS II coil in the menu and it is a DEUS II again
Software DEUS II V4.1 is the newest release as of our October 30, 2026 check Updates the remote and headphones together over USB through XP's online updater
Battery One Li-ion 18650 cell, 11 Wh, in the front coil; more than 10 hours; about 4 hours to charge over USB-C from a 1 A or stronger charger A full day on one charge; the remote and headphones charge separately
Weight and length 2.9 kg (6.4 lb) with the remote; 1.20 m (3.94 ft) assembled; 5.8 kg (12.8 lb) in the included XP case Single-person use; the handle and support adjust for balance and search height
Weather Waterproof construction for rain and challenging conditions; case rain and shock proof A land survey machine; not submersible, no IP rating published for the unit
Programs 1 factory program plus 2 user programs Save a quiet-site setup and a deep-field setup and switch between them
Warranty Five years parts and labor; batteries and connectors two years XP's detector-grade warranty on a machine XP itself labels an accessory

One remote, two machines: the DEUS II remote that runs the Xtrem Hunter also runs every standard DEUS II FMF search coil, so the workflow XP describes is to mark a deep target with the two-box, then switch to a 9 in (22.5 cm) or 11 in (28 cm) DEUS II coil from the coil list, in the Relic program, to confirm it at moderate depth before the big dig. A long press of MENU marks the spot on XP's Go Terrain app, so a survey leaves a map, not a memory.

Who the XTR-115E Is For, and Who Should Buy the Complete Kit Instead

Best for: the DEUS II owner who hunts old homesteads, hoard sites, battlefields or survey ground and keeps walking over signals a swing coil cannot reach: a cache hunter, relic hunter, archaeologist or utility locator who already carries the remote and wants the two-box frame without paying for a second controller and headphones. Experience level: advanced. You already know the DEUS II menus; the Xtrem Hunter adds a non-motion threshold, a signal graph instead of a target ID, and the discipline of stripping every piece of metal off your body. Same-brand alternative: if you do not own a DEUS II remote, or you want a dedicated remote and headphones that stay on the frame, the Xtrem Hunter complete kit (XTR-115RCWSA2XLEA) includes both. Same-brand step down: for coins, jewelry and relics at ordinary depth your DEUS II with a standard FMF coil already is the tool; for gold nuggets, the DEUS II GOLD FIELD program with the HF2 elliptical coil. There is no XP step up: the Xtrem Hunter is XP's deepest machine.

Honest limits: the remote must be on V2.0 or higher before it will pair, and a launch-era remote needs the free update first; no charger is in this kit; it is designed not to hear coins, jewelry or nuggets; nothing in the system is submersible; and there is no target ID beyond the IAR iron test. As a specialist deep-seeking unit it is a final sale under our refund policy, so call before you order if you are unsure your remote qualifies.

Xtrem Hunter Settings That Matter

There is no target ID to read on a two-box machine; what you set is how much of the ground, the interference and the surface trash the Xtrem Hunter lets through. XP's manual gives every control a range and a factory value, printed here so you are never guessing, and its own start-of-session order is: pair the frame as a new coil, set the handle so the frame rides well above the surface, strip every piece of metal off your body, run a Frequency Scan, retune, then walk. Change one setting at a time and listen to what it did before you touch the next.

  • Search height (the handle, not a menu): the manual's first field instruction is to adjust the handle so the frame stays far enough from the ground to avoid excessive sensitivity to surface targets. In trashy or iron-filled ground, raise it further, or hold the aluminum frame itself; height is the Xtrem Hunter's first discrimination control.
  • Sensitivity (0 to 99, factory 85): the most commonly used range is 70 to 90. Cut it to 60 to 75 in trash, near power lines, fences or radio relays, and never test indoors, where urban interference swamps the machine.
  • Reactivity (1 to 3, factory 1): low Reactivity is the depth setting: best depth, electromagnetic interference and small targets cancelled, longer signals, less noise from frame movement, and a slower walking pace to match. High Reactivity pinpoints faster with shorter signals and separates targets in cluttered ground. Do not change it often if you want to read sizes on the graph consistently.
  • Threshold (0 to 20, factory 0): raises the background hum to mask small variations, which quiets noise but can also bury faint and deep targets. Use it in moderation; a short press of the retune key recenters the hum at any time.
  • Auto Tune (OFF to 3, factory OFF): automatic threshold tracking at three speeds. With it on, holding the frame still over a target fades the signal within seconds, and a fast setting can tune out a very large deep mass or a long pipe. Switch it OFF to pinpoint in pure non-motion.
  • Frequency Scan (Freq. Shift, 14 channels, auto scan or manual): start every session with the automatic scan, a long press of the top-right key, which picks the quietest of the 14 channels. If noise remains, lower Sensitivity, then Reactivity, then Audio Response, in that order.
  • Audio Response (1 to 4, factory 2): higher settings amplify deep targets and make the machine more jittery; 1 gives the most stable threshold and the least ground noise. The manual calls it the key control over the ground response, so set it to your site.
  • Ground (59 to 95, factory 87): thanks to FMF the factory 87 works in most cases. In unusually magnetic ground, grab it (hold the ground key two seconds, tilt the front coil toward the ground until the hum settles, release and read the value) or set it manually lower.
  • Discri IAR (OFF, 3 or 5; factory OFF): Iron Amplitude Rejection by distance from the coils. 3 rejects shallow iron, 5 rejects shallow and deeper iron; rejected iron gives a low tone and gray on the graph. It works only while you are moving; stop over a target and the audio reverts to the mid tone. In iron-filled ground it can mask large deep targets, so raise the frame instead of pushing IAR higher.
  • Audio Type (Square or Pulse, factory Square): Square keeps fixed harmonics and changes only volume with depth and size; Pulse gives stronger sound dynamics and better deep-target perception, through headphones only, never the built-in speaker or a bone-conduction set. A 4-band equalizer sits behind both.

What the 5 m claim and the screen do not do. The frame is not a depth meter: signal strength on the 4-second graph estimates depth and signal duration estimates size, and the manual's reference target is 30 cm (12 in) across, so a coin will not register at any depth. There is no target ID and no discrimination beyond the IAR iron test. It detects only on its bottom side; passing a test target over the top moves the threshold the wrong way, and laying the frame on its side at 90 degrees invites interference. Always wear headphones: the audio range is so wide that the built-in speaker hides the faintest signals. To test one without buried targets, lay out metal samples from 25 cm (10 in) to more than 1 m (3 ft) and pass the frame over them at arm height, about 1.5 m (5 ft).

Where the Xtrem Hunter Works Well, and Where It Does Not

Old homesteads, campgrounds and hoard country: the ground it exists for. Caches, strongboxes and large relics sit below the reach of a swing detector and under the surface trash that defeats it. Grid the site at walking pace on Reactivity 1, mark every single-lobe signal, confirm with a DEUS II coil before you dig.

Battlefields and artillery ground: shells, large shell fragments, cannon parts and buried wagon iron are exactly the moderate-to-large masses the two-box hears, while small targets such as nails and bullets stay invisible to it by design. IAR 3 or 5 separates the horseshoe-class iron from the non-ferrous mass when you need it; raise the frame where the iron is thick.

Construction, utilities and property surveys: tanks, pipes, septic lids, conduit and buried metal structures, located by one person without a second operator. Auto Tune OFF when tracing a long pipe so the tracking does not tune the pipe out.

Beaches above the waterline and open fields: wide, clean ground is where a two-box covers the most area per hour. The construction withstands rain and wet ground; the frame, the remote and the headphones are never submerged.

Towns, power lines and radio masts: the hardest ground for it. XP calls the Xtrem Hunter a highly sensitive device and tells you to keep away from industrial areas, houses and power lines; where you must work near them, Frequency Scan first, then Sensitivity down to 60 to 75, Reactivity and Audio Response down, and expect reduced depth.

Where it is the wrong buy: for coins, jewelry, buttons and gold nuggets, which it is designed not to hear; for anything under water, since no part of the system is submersible; for a hunter who wants a target ID before the dig; and for anyone who will not strip the metal off their body, because the frame, boot shanks and belt buckles falsify its tuning. It is a specialist deep-target survey tool for the hunter who already knows a large target is down there.

Coils, Headphones and Accessories That Fit the Xtrem Hunter

The Xtrem Hunter's own coils are the XTR115 TX and RX pair on the XTR-STEM; XP sells them only in the two kits (the complete kit and the XTR-115E) and as repair parts. Everything else that fits it is DEUS II ecosystem gear, because the DEUS II remote is its controller, and every item below is a product we stock and list on our XP DEUS II fitment page.

Pinpointing coils for the same remote. XP's workflow is two-box first, swing coil second: pair a standard DEUS II FMF coil to the remote and select it from the coil list to confirm a deep target before you dig. The 11 in (28 cm) FMF coil is the all-round confirmation coil, the 9 in (22.5 cm) FMF coil separates best in iron, and the 13x11 in (34x28 cm) FMF coil covers the most ground. (XP's X35 and HF coils are for the original DEUS and the ORX; they do not pair with a DEUS II remote.)

Headphones. Headphones pair with the DEUS II remote, not with the frame, and the manual says to always use them. XP's manual names the WS6, WSA II and WSA II XL by model; XP's V4.1 release lists the remote control, WS6, WSA II (XL), WS6 ST and WSA (XL) ST as the compatible ecosystem, and the remote and headphones must always run the same version. We stock the current ST line: WSA XL ST over-ear headphones, WSA ST headphones and the WS6 ST headphones with control unit. Call before you pair a set you already own to an Xtrem Hunter and we will check the version with you. The Pulse audio type needs headphones; it is not available through the speaker or the BH-01 bone-conduction set.

Pinpointer, carry and finds. The XP MI-6 pinpointer pairs to the same remote and its audio comes through your headphones; the manual also tells you to check your boots with a pinpointer for wire mesh before you start. The XP Backpack 280 is the carry option XP names for the Xtrem Hunter beside the included XTR-CASE115 case, and the XP Finds Pouch carries what a two-box dig turns up.

XP Backpack 280 (optional) or XP hard case (included) for the Xtrem Hunter XTR-115 kit

Frequently Asked Questions

Do I need a DEUS II for the XTR-115E, and which one?

Yes. The XTR-115E is the frame, coils, stem and case only; XP's manual says to ensure your DEUS II remote control is up to date with Version 2.0 or higher, then pair the Xtrem Hunter as a new coil (Option, Pairing, Coil, enter its serial number). Any DEUS II package that includes the remote control qualifies once the remote is updated; the version shows on the screen at start-up, and XP's online updater brings a launch-era remote up for free over USB. If you do not own a DEUS II remote, the complete kit (XTR-115RCWSA2XLEA) includes one along with WSA II-XL headphones.

Does the XTR-115E include a charger, headphones or a remote?

No to all three. The kit holds the two coils on the frame, the S-Telescopic stem, the USB-C charging cable, the fasteners and strap, the manual and the XTR-CASE115 case. Charge the front coil from any USB charger rated 1 A or more, including the one that came with your DEUS II; use the headphones already paired to your remote. The complete kit (XTR-115RCWSA2XLEA) is the configuration that adds a remote, WSA II-XL headphones and a charger.

Which Xtrem Hunter kit should I buy, the complete kit or the XTR-115E?

XP sells one Xtrem Hunter two ways, each a factory part number. The complete kit (XTR-115RCWSA2XLEA) is the standalone configuration: the XTR115 TX and RX coils, the S-Telescopic stem, a DEUS II remote control, WSA II-XL wireless headphones, the USB-C cable and US charger, and the XTR-CASE115 case, for the hunter who does not own a DEUS II. The XTR-115E upgrade kit holds the coils, the stem, the USB-C cable, the fasteners, the strap and the case only, with no remote, no headphones and no charger, for the hunter who already owns a DEUS II remote on V2.0 or higher; one remote then runs both machines. This page is the Xtrem Hunter XTR-115E upgrade kit (XTR-115E): coils, stem, USB-C cable, fasteners, strap, manual and case, no remote, headphones or charger.

How deep can the XP Xtrem Hunter detect?

XP rates it to large targets up to 5 m (16 ft) deep, and that figure is a large-target ceiling, not a coin depth. The manual's own signal examples use a 30 cm (12 in) target: a clear double-lobe signal at 30 cm (12 in), a strong first lobe at 60 cm (24 in), and at more than 1 m (3 ft) a clear but faint single signal. Target size, shape, orientation, the ground and your Sensitivity and Reactivity settings decide what you hear; for maximum depth the manual's recipe is clean, non-mineralized ground, a Frequency Scan, lower Reactivity (Ground 70 with Reactivity 1 for deep non-ferrous targets), higher Sensitivity and Audio Response, and headphones.

Can the Xtrem Hunter find gold, coins or jewelry?

It will not find gold nuggets, coins or jewelry, and it is designed that way. The two-box geometry makes small surface targets naturally invisible to it so that it can hear large masses at depth; XP's reference target is 30 cm (12 in) across. Gold enters its world only at cache scale: strongboxes, hoards, large artifacts. For coins, jewelry and relics the XP DEUS II with a standard FMF coil is the tool, and the same remote runs both; for nuggets, the DEUS II's GOLD FIELD program with the HF2 elliptical coil is XP's small-gold setup.

Is the XP Xtrem Hunter waterproof?

Its construction withstands rain and challenging conditions, and the XP case is rain and shock proof, but no part of the system is submersible and XP publishes no IP rating for the frame or the remote. Keep your DEUS II remote and headphones to their own ratings (the ST headphones are rainproof, the WSA XL ST handles 1 m / 3 ft). It is a land survey machine.

What settings should I change first on the Xtrem Hunter?

Follow the manual's ten key points. Pair the frame as a new coil (Option, Pairing, Coil, enter its serial number) and the remote switches to the Xtrem Hunter interface. Adjust the handle so the frame rides well above the surface. Take every piece of metal off your body, boots and belt included. Long-press the top-right key for the automatic Frequency Scan across the 14 channels. Leave Sensitivity at the factory 85 (common range 70 to 90), Reactivity at 1, Threshold at 0, Auto Tune OFF, Audio Response at 2 and Ground at 87, press the retune key, and walk, retuning regularly. If the site is noisy, cut Sensitivity to 60 to 75 and Audio Response to 1 and raise the frame. To confirm a target, switch Auto Tune OFF, retune, and move slowly around it; raising Reactivity speeds up the pinpoint.

How long does the Xtrem Hunter battery last, and how do you charge it?

More than 10 hours per charge from one Li-ion 18650 cell (11 Wh, 45 g) built into the front coil, which also carries the wireless transmitter; the back coil connects to it by cable. A full charge takes about 4 hours over the included USB-C cable from any USB charger rated 1 A or more, between 0 and 40 C (32 and 104 F). The DEUS II remote and the wireless headphones have their own batteries and charge separately; XP warrants batteries and connectors for two years and the detector for five.

What headphones and accessories fit the Xtrem Hunter?

Headphones pair with the DEUS II remote, and the manual names the WS6, WSA II and WSA II XL; XP's V4.1 release lists the remote as compatible with the remote control, WS6, WSA II (XL), WS6 ST and WSA (XL) ST, as long as remote and headphones run the same version. We stock the WSA XL ST, WSA ST and WS6 ST. For confirming deep targets, any standard DEUS II FMF coil pairs to the same remote: the 11 in (28 cm) all-rounder, the 9 in (22.5 cm) separator or the 13x11 in (34x28 cm) coverage coil (X35 and HF coils are for the original DEUS and ORX and do not pair). The MI-6 pinpointer pairs to the remote, the XP Backpack 280 is the carry option XP names, and the Finds Pouch carries the recoveries. Every one is listed on our XP DEUS II fitment page.

Does the Xtrem Hunter need a software update, and which version?

The Xtrem Hunter runs on the DEUS II remote's software and has no separate version of its own. The remote must be V2.0 or higher to pair it; V2.0 is the release that added the Xtrem Hunter interface, V3.0 added the Pulse audio type for it, and as of our October 30, 2026 check DEUS II V4.1 is the newest release, with corrections for the XTREM HUNTER. Update the remote and your wireless headphones to the same version through XP's online updater over USB, because mismatched versions will not work together; if your headphones are the WSA II or WSA II XL, go straight to V4.1 or later rather than V4.0, which worked only with the ST stereo headsets. Updates are free.

Can one person carry and run the Xtrem Hunter?

Yes. XP designed it for single-person use: 2.9 kg (6.4 lb) with the remote fitted, 1.20 m (3.94 ft) long assembled, with a handle and support that adjust for balance and search height and a carrying strap whose anchor point moves to suit your height. In the included rain and shock proof XP case it is 5.8 kg (12.8 lb), the case alone 2.7 kg (6 lb), and the case measures 725 x 480 x 170 mm (28 x 18.9 x 6.7 in), so it travels as one piece of luggage.

Where can I buy the XP Xtrem Hunter online from an authorized dealer?

Here. History Seekers Metal Detectors is an authorized XP dealer; every Xtrem Hunter kit we sell is new, comes from XP's authorized US distributor under its factory part number, and carries XP's five-year parts and labor warranty (batteries and connectors two years). As a specialist deep-seeking unit it is a final sale under the History Seekers refund policy, so call 256-284-2247 before you order if you have any doubt about which kit fits your DEUS II, and we will talk it through. We price match: send us a competitor's current listing for a new unit and we will verify it.


Who you are buying from

History Seekers is a small American business and a working detecting channel: over 1.1 million people follow our hunts on Facebook and YouTube. Everyone here detects, from the top down: gold, relics, coins, jewelry, even float copper. We hunt with the gear we sell, and the person who answers your call has real dirt time. Every purchase keeps everyday Americans working.

The story is more important than the artifact.

See everything that fits your machine:What Fits the XP Deus II

You may also like

Recently viewed